Audi / A8 D4 (4H) / 34 - Clearance height control LUFE-DAEMPFER [EV_AirSuspe 003017] / Setting of the zero point of the height adjustment system

Search: Search area:

Mark	Model	Control unit	Diagnostic operation

Mark

Select a vehicle make or a common group such as Service Intervals, Engines, Transmissions, Immobilizers and Independent Heaters.

Model

Control unit Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.

Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.

Diagnostic operation Select the desired diagnostic procedure.

Diagnostic procedure

This operation was considered useful 2x.

You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.

Log-in

Note:
done after replacement of component:
- adaptive air suspension
- adaptive air suspension - control unit
- vehicle ride height sensor

Conditions:
- ignition = ON
- The vehicle must be standing on a level surface
- vehicle must not be loaded with people or luggage
- all doors - closed
- Workshop jack mode OFF
- residual fuel volume in tank > &fracXX;

Conditions MMI menu:
- wheel change = OFF

Warning
The vehicle may be set to a different position during this operation !!!

Using the suspension characteristics selector, set COMFORT mode

connect with the control unit XX - clearance height control

XX - Security access

enter value: XXXXX

Start

XX - Basic settings

select item in drop-down menu: IDEXXXXX - activation Regulation of the vehicle height

Warning
The vehicle may be set to a different position during this operation!!!

Start

follow the diagnostics instructions

required value: Successfully completed

to achieve the values - continue

XX - Basic settings

select item in drop-down menu: IDEXXXXX - Delete: calibration Regulation of the vehicle height

Warning
The vehicle may be set to a different position during this operation!!!

Start

follow the diagnostics instructions

required value: Successfully completed

to achieve the values - continue

XX - Basic settings

select item in drop-down menu: IDEXXXXX - Start at reference level

Warning
The vehicle may be set to a different position during this operation!!!

Start

follow the diagnostics instructions

required value: Successfully completed

to achieve the values - continue

LF wheel

XX - Adaptation

select item in drop-down menu: IDEXXXXX - Body height - in front left

For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window

measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value

for instance: distance XXXmm enter as XXX
Start

RF wheel

XX - Adaptation

select item in drop-down menu: IDEXXXXX - Body height - in front right side

For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window

measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value

for instance: distance XXXmm enter as XXX

Start

LR wheel

XX - Adaptation

select item in drop-down menu: IDEXXXXX - Body height - in rear left

For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window

measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value

for instance: distance XXXmm enter as XXX

Start

RR wheel

XX - Adaptation

select item in drop-down menu: IDEXXXXX - Body height - in rear right side

For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window

measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value

for instance: distance XXXmm enter as XXX

Start

XX - Basic settings

select item in drop-down menu: IDEXXXXX - calibration Regulation of the vehicle height

Warning
The vehicle may be set to a different position during this operation!!!

Start

follow the diagnostics instructions

required value: Successfully completed

to achieve the values - continue

XX - Basic settings

select item in drop-down menu: IDEXXXXX - activation Regulation of the vehicle height

Warning
The vehicle may be set to a different position during this operation!!!

Start

follow the diagnostics instructions

required value: Successfully completed

to achieve the values - end

Log-in