Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
Audi / Q7 (4L) / 6C - reverse camera (J772__Rearview) CAN / calibration
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
This operation was considered useful 1x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Note:
- done after replacement of component: rear camera, rear camera - control unit
- done after repair of components: rear axle, rear section of the vehicle
Conditions:
- install calibration jig (VAS XXXX)
- the vehicle must stand on even ground
- the vehicle must not be moved
- tailgate - closed
- control - straight direction - steering wheel turn angle = X.X°
- ignition = ON
- engine speed = X
- rear camera - active
- MMI shows the picture from the reverse camera
- for height-adjustable vehicles, set the automatics
connect with the control unit XC - Reverse camera
XX - Security access
enter value: XXXXX
Start
XX - Adaptation channel XXX - height
measure the height from the floor to the camera [mm] = B
enter value: height B (measured value)
for instance: height XXXXmm enter as XXXX
Test
Save
XX - Adaptation channel XXX - height
measure the height of the calibration jig from the floor [mm] = H
basic value = XXXmm
enter value: XXX + height H (measured value)
for instance: height XXmm enter as XXX (XXXmm+XXmm)
Test
Save
XX - Adaptation channel XXX - distance
measure the distance of the calibration jig from the rear axle [mm] = A
enter value: XXXXX - wheelbase - A (measured value)
wheelbase
Amarok (XH) = XXXX mm
Passat (XC) = XXXX mm
Passat CC (XX) = XXXX mm
Passat (XX) = XXXX mm
Phaeton (XD) = XXXX mm
Phaeton (XD) Long = XXXX mm
Sharan (XN)
Alhambra (XN) = XXXX mm
Tiguan (XN) = XXXX mm
Touareg (XL) = XXXX mm
Transporter/Multivan (XE) = XXXX mm
Transporter/Multivan (XF) Long = XXXX mm
for instance: Passat (XC) enter as XXXXX (XXXXX - XXXX - A (measured value = XXXX) )
Test
Save
XX - Adaptation channel XXX - storage of values
enter value: X
Test
Save
Test
XX - Measured values group XXX
required values:
field X = XxXXXX (Calibration - status)
XX - end of communication
Created on: X.XX.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
- done after replacement of component: rear camera, rear camera - control unit
- done after repair of components: rear axle, rear section of the vehicle
Conditions:
- install calibration jig (VAS XXXX)
- the vehicle must stand on even ground
- the vehicle must not be moved
- tailgate - closed
- control - straight direction - steering wheel turn angle = X.X°
- ignition = ON
- engine speed = X
- rear camera - active
- MMI shows the picture from the reverse camera
- for height-adjustable vehicles, set the automatics
connect with the control unit XC - Reverse camera
XX - Security access
enter value: XXXXX
Start
XX - Adaptation channel XXX - height
measure the height from the floor to the camera [mm] = B
enter value: height B (measured value)
for instance: height XXXXmm enter as XXXX
Test
Save
XX - Adaptation channel XXX - height
measure the height of the calibration jig from the floor [mm] = H
basic value = XXXmm
enter value: XXX + height H (measured value)
for instance: height XXmm enter as XXX (XXXmm+XXmm)
Test
Save
XX - Adaptation channel XXX - distance
measure the distance of the calibration jig from the rear axle [mm] = A
enter value: XXXXX - wheelbase - A (measured value)
wheelbase
Amarok (XH) = XXXX mm
Passat (XC) = XXXX mm
Passat CC (XX) = XXXX mm
Passat (XX) = XXXX mm
Phaeton (XD) = XXXX mm
Phaeton (XD) Long = XXXX mm
Sharan (XN)
Alhambra (XN) = XXXX mm
Tiguan (XN) = XXXX mm
Touareg (XL) = XXXX mm
Transporter/Multivan (XE) = XXXX mm
Transporter/Multivan (XF) Long = XXXX mm
for instance: Passat (XC) enter as XXXXX (XXXXX - XXXX - A (measured value = XXXX) )
Test
Save
XX - Adaptation channel XXX - storage of values
enter value: X
Test
Save
Test
XX - Measured values group XXX
required values:
field X = XxXXXX (Calibration - status)
XX - end of communication
Created on: X.XX.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.