Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
Engines / Diesel / 2.0/103kW TDI-CR CFFx;CFGx;CFHx;CLCx;CMGB UDS EDC17 C46 / creation of Readiness
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
This operation was considered useful 1x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Conditions:
- engine speed = idling
- Error memory empty
- on-board voltage > XX.X V
- fuel tank contents > XXl
- ambient temperature > X°C
- clogging of Diesel particulate filter < XXg
- Start-Stop inactive
connect with the control unit XX - engine
XX - Security access
enter value:
XXXXX = function accessible: adaptation, coding, basic settings
Start
XX - Basic settings
select item in drop-down menu: IDEXXXXX - Automatic test procedure
Start
follow the diagnostics instructions (depress and hold brake pedal)
required values: Successfully completed
if values are not achieved -> check of error memory
XX - end of communication
Subsequent Readiness BITS can be set only by test driving the vehicle:
- Regulation of filling pressure
- Check of clogging level of Diesel particulate filter
- Test - Lambda sensor(s)
- Test - catalyst SCR
- Test - oxidation catalyst
Note:
- observe the occupation safety rules when taking a test drive with connected diagnostics tester
Regulation of filling pressure - settings
In Xrd gear at a minimum engine speed of XXXX rpm accelerate to full load without Kick-down - duration: MIN Xs
Check of clogging level of Diesel particulate filter - settings
Conditions:
- Time since last regeneration > XXMIN
- ambient temperature > -X°C
do a test drive:
- duration - must be minimum: XMIN
- XXx akceleraion -> deceleration -> akceleraion
- accelerator pedal MAX. XX%
further, do:
do a test drive:
- duration - must be minimum: XXs
- engine speed MIN. XXXX rpm
- engaged gear: X.
end
- engine speed = idling
- Error memory empty
- on-board voltage > XX.X V
- fuel tank contents > XXl
- ambient temperature > X°C
- clogging of Diesel particulate filter < XXg
- Start-Stop inactive
connect with the control unit XX - engine
XX - Security access
enter value:
XXXXX = function accessible: adaptation, coding, basic settings
Start
XX - Basic settings
select item in drop-down menu: IDEXXXXX - Automatic test procedure
Start
follow the diagnostics instructions (depress and hold brake pedal)
required values: Successfully completed
if values are not achieved -> check of error memory
XX - end of communication
Subsequent Readiness BITS can be set only by test driving the vehicle:
- Regulation of filling pressure
- Check of clogging level of Diesel particulate filter
- Test - Lambda sensor(s)
- Test - catalyst SCR
- Test - oxidation catalyst
Note:
- observe the occupation safety rules when taking a test drive with connected diagnostics tester
Regulation of filling pressure - settings
In Xrd gear at a minimum engine speed of XXXX rpm accelerate to full load without Kick-down - duration: MIN Xs
Check of clogging level of Diesel particulate filter - settings
Conditions:
- Time since last regeneration > XXMIN
- ambient temperature > -X°C
do a test drive:
- duration - must be minimum: XMIN
- XXx akceleraion -> deceleration -> akceleraion
- accelerator pedal MAX. XX%
further, do:
do a test drive:
- duration - must be minimum: XXs
- engine speed MIN. XXXX rpm
- engaged gear: X.
end
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.