Engines / Diesel / 6.0 TDI CR / basic settings

Search: Search area:

Mark	Model	Control unit	Diagnostic operation

Mark

Select a vehicle make or a common group such as Service Intervals, Engines, Transmissions, Immobilizers and Independent Heaters.

Model

Control unit Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.

Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.

Diagnostic operation Select the desired diagnostic procedure.

Diagnostic procedure

You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.

Log-in Buy

Conditions:
- engine temperature > XX °C
- number of faults = X

exhaust recirculation

connect with the control unit XX - engine

shortly switch-off the ignition, Start the engine

XX - Basic settings group XXX
Start

depress brake pedal
depress clutch pedal

engine speed = XXX - XXXX rpm

required values - EGR active
field X = XXX - XXXX rpm (engine speed)
field X = XXX - XXX mg/stroke (intake air volume cylinder row X)
field X = XXX - XXX mg/stroke (intake air volume cylinder row X)

required values - EGR inactive
field X = XXX - XXXX rpm (engine speed)
field X = XXX - XXX mg/stroke (intake air volume cylinder row X)
field X = XXX - XXX mg/stroke (intake air volume cylinder row X)

Basic settings - turbo blower

connect with the control unit XX - engine

shortly switch-off the ignition, Start the engine

XX - Basic settings group XXX
Start

depress brake pedal
depress clutch pedal

engine speed = approx XXXX rpm

required values - turbo blower X = ON
field X = XXXX - XXXX rpm (engine speed)
field X = XXX - XXX mg/stroke (intake air volume cylinder row X)
field X = XX - XXX mg/stroke (intake air volume cylinder row X)

required values - turbo blower X = ON
field X = XXXX - XXXX rpm (engine speed)
field X = XX - XXX mg/stroke (intake air volume cylinder row X)
field X = XXX - XXX mg/stroke (intake air volume cylinder row X)

Basic settings - flap in intake manifold

connect with the control unit XX - engine

shortly switch-off the ignition, Start the engine

XX - Basic settings group XXX
Start

depress brake pedal
depress clutch pedal

engine speed = approx XXXX rpm

required values - flap in intake manifold = open
field X = XXXX - XXXX rpm (engine speed)
field X = XXX - XXX mg/stroke (intake air volume cylinder row X)
field X = XXX - XXXX mg/stroke (intake air volume cylinder row X)

required values - flap in intake manifold = closed
field X = XXXX - XXXX rpm (engine speed)
field X = XXX - XXXX mg/stroke (intake air volume cylinder row X)
field X = XXX - XXX mg/stroke (intake air volume cylinder row X)

Basic settings - by-pass valve of cooler for the exhaust gas recirculation

XX - Basic settings group XXX
Start

wait

the control unit increases the engine speed -> approx XXXX/MIN

required values:
field X = approx XXXX/MIN (engine speed)
field X = by-pass valve of cooler for the exhaust gas recirculation - closed / open

programming - kick-down

connect with the control unit XX - engine

shortly switch-off the ignition, Start the engine

XX - Basic settings group XXX
Start

depress accelerator pedal

required values:
field X = ADP-OK

wait XX s

switch ignition off for XX s

Created on: XX.XX.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.

Log-in Buy