Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
Engines / Diesel / EDC 17 UDS general / bleeding (deaeration) - Engine cooling
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
This operation was considered useful 5x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Conditions:
- engine speed = idling
- parking brake = ON
- automatic transmission = N or P
- fill the cooling system in a conventional manner - use the assembly jig VAS XXXX
- on-board voltage > XXV
- the vehicle must stand on even ground
- DPF regeneration - is in state - OFF
Note:
- duration: approx X - XX MIN.
connect with the control unit XX - engine
XX - Adaptation
select item in menu: IDEXXXXX - bleeding (deaeration) - Engine cooling
TIP! For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window
new value -> enter value: XX (active)
Start
XX - Security access
enter value: XXXXX
Start
XX - Basic settings
select item in menu: IDEXXXXX - Test - bleeding (deaeration): Engine cooling
Start
follow the diagnostics instructions…
desired condition:
- Successfully completed
XX - Basic settings - Stop
XX - end of communication
switch-off the ignition
wait Xs
Start the engine
connect with the control unit XX - engine
XX - Security access
enter value: XXXXX
Start
XX - Basic settings
select item in menu: IDEXXXXX - Test - bleeding (deaeration): Engine cooling
Start
follow the diagnostics instructions…
desired condition:
- Successfully completed
XX - Basic settings - Stop
XX - Actuators
select item in drop-down menu: IDEXXXXX - control unit: throttle valve
XX - Actuators - Start
wait XXs
XX - Actuators - Stop
switch-off the ignition
wait XXs
Start the engine
Advanced Measured Values
select item in menu: IDEXXXXX - coolant temperature
TIP! For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window
required value:
XX°C
fully depress: accelerator pedal
wait XXXs
XX - end of communication
Test: coolant: status
End of test
- engine speed = idling
- parking brake = ON
- automatic transmission = N or P
- fill the cooling system in a conventional manner - use the assembly jig VAS XXXX
- on-board voltage > XXV
- the vehicle must stand on even ground
- DPF regeneration - is in state - OFF
Note:
- duration: approx X - XX MIN.
connect with the control unit XX - engine
XX - Adaptation
select item in menu: IDEXXXXX - bleeding (deaeration) - Engine cooling
TIP! For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window
new value -> enter value: XX (active)
Start
XX - Security access
enter value: XXXXX
Start
XX - Basic settings
select item in menu: IDEXXXXX - Test - bleeding (deaeration): Engine cooling
Start
follow the diagnostics instructions…
desired condition:
- Successfully completed
XX - Basic settings - Stop
XX - end of communication
switch-off the ignition
wait Xs
Start the engine
connect with the control unit XX - engine
XX - Security access
enter value: XXXXX
Start
XX - Basic settings
select item in menu: IDEXXXXX - Test - bleeding (deaeration): Engine cooling
Start
follow the diagnostics instructions…
desired condition:
- Successfully completed
XX - Basic settings - Stop
XX - Actuators
select item in drop-down menu: IDEXXXXX - control unit: throttle valve
XX - Actuators - Start
wait XXs
XX - Actuators - Stop
switch-off the ignition
wait XXs
Start the engine
Advanced Measured Values
select item in menu: IDEXXXXX - coolant temperature
TIP! For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window
XX°C
fully depress: accelerator pedal
wait XXXs
XX - end of communication
Test: coolant: status
End of test
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.