Engines / Petrol / 1.6/75kW APF; AVU / 15-Readiness Code - creation

Search: Search area:

Mark	Model	Control unit	Diagnostic operation

Mark

Select a vehicle make or a common group such as Service Intervals, Engines, Transmissions, Immobilizers and Independent Heaters.

Model

Control unit Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.

Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.

Diagnostic operation Select the desired diagnostic procedure.

Diagnostic procedure

This operation was considered useful 1x.

You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.

Log-in

Conditions:
- appliances OFF
- engine temperature > XX °C (XX - Measured values group XXX field X)
- catalyst temperature > XXX °C (XX - Measured values group XXX field X)
- intake air temperature > XX °C (XX - Measured values group XXX field X)
- catalyst temperature > XXX °C (XX - Measured values group XXX field X)
- number of faults = X

Start the engine

connect with the control unit XX - engine

XX - Measured values group XXX
required values:
field X = ADP-OK (may take several minutes)

if values are not achieved execute function: XX - Basic settings

XX - Measured values group XXX
required values:
field X = ADP-OK (may take several minutes)

if values are not achieved execute function: XX - Basic settings

Start the engine - rear window heating = ON

XX - Measured values group XXX
required values:
field X = XX °C (engine temperature)
field X = XXX s

XX - Basic settings group XXX
Start

required values:
field X = XXX (Lambda-sensor upstream of catalyst)

increase rpm to XXXX až XXXX rpm

required values:
field X = XXx or XXX (Lambda-sensor downstream of catalyst)

now only: engine < XX/XX

XX - Basic settings group XXX
Start

increase rpm to XXXX až XXXX rpm

required values:
field X = X-XXX(Xx)

engine speed = idling

XX - Basic settings group XXX
Start

increase rpm to XXXX až XXXX rpm

required values:
field X = > XXX °C
field X = TEST ON

wait

required values:
field X = BX-SX OK

engine speed = idling

XX - Basic settings group XXX
Start
required values:
field X = > XXX °C
field X = TEST ON

wait

required values:
field X = TBV OK

XX - Basic settings group XXX
Start
required values:
field X = > XXX °C
field X = TEST ON

wait

required values:
field X = TBV OK

XX - Basic settings group XXX
Start

depress and hold - brake pedal

required values:
field X = TEST ON

wait

required values:
field X = BX-SX OK

permit - brake pedal

XX - Basic settings group XXX
Start

depress and hold - brake pedal

required values:
field X = TEST ON

wait

required values:
field X = BX-PX OK

permit - brake pedal

XX - Basic settings group XXX
Start

increase rpm to XXXX-XXXX rpm

required values:
field X = XXX C°
field X = TEST ON

wait

required values:
field X = CAT BX OK

engine speed = idling

now only: engine > XX/XX

XX - Basic settings group XXX
Start

depress and hold - brake pedal
fully depress - accelerator pedal

engine speed = approx XXXX oz/MIN

required values:
field X = XXX C°
field X = TEST ON

wait

required values:
field X = BX-PX OK

permit: brake pedal, accelerator pedal

XX - Basic settings group XXX
Start
required values:
field X = XXX C°
field X = TEST ON

wait

required values:
field X = TBV OK

XX - Basic settings group XXX
Start
required values:
field X = XXX C°
field X = TEST ON

wait

required values:
field X = Syst OK

XX - Basic settings group XXX
Start

depress and hold - brake pedal

required values:
field X = XXX C°
field X = TEST ON

wait

required values:
field X = BX-SX OK.

permit - brake pedal

XX - Basic settings group XXX
Start

depress and hold - brake pedal

required values:
field X = XXX C°
field X = TEST ON

wait

required values:
field X = BX-SX OK.

permit - brake pedal

XX - Basic settings group XXX
Start

depress and hold - brake pedal
fully depress - accelerator pedal

engine speed = approx XXXX rpm

required values:
field X = XXX C°
field X = TEST ON

wait

required values:
field X = CAT BX OK.

permit: brake pedal, accelerator pedal

end

if values are not achieved - check of error memory

check download of the readiness code of the readiness functions

Created on: XX.XX.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.

Log-in