Engines / Petrol / 2.0/110kW FSI BLR / creation of Readiness (223)

Search: Search area:

Mark	Model	Control unit	Diagnostic operation

Mark

Select a vehicle make or a common group such as Service Intervals, Engines, Transmissions, Immobilizers and Independent Heaters.

Model

Control unit Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.

Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.

Diagnostic operation Select the desired diagnostic procedure.

Diagnostic procedure

You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.

Log-in Buy

Conditions:
- engine temperature >= XX °C (XX - Measured values group XXX field X)
- catalyst temperature > XXX °C (XX - Measured values group XXX field X)
- parking brake = ON
- gear engaged (P) (automatic transmission)
- on-board voltage > XX V (XX - Measured values group XXX field X)

Note:
- The readiness Code must be created as the last diagnostics task. Later deletion of the memory could also result in deletion of the created readiness Code.

connect with the control unit XX - engine

Start the engine - engine speed = idling

wait XX MIN

XX - Basic settings group XXX
activate default settings

wait XX s (follow the diagnostics instructions)

required values
field X = ADP-OK

upon achievement of values - continue

XX - Basic settings group XXX
activate default settings

wait

required values
field X = Syst. OK

upon achievement of values - continue

XX - Basic settings group XXX
activate default settings

increase rpm to XXXX - XXXX rpm

required values
field X > XXX °C
field X = Cat BX OK

upon achievement of values - release - accelerator pedal

XX - Basic settings group XXX
activate default settings

fully depress - brake pedal + accelerator pedal

required values
field X = Test OFF -> TEST ON

wait

required values
field X = BX-SX OK

upon achievement of values - release - brake pedal + accelerator pedal

XX - Basic settings group XXX
activate default settings

fully depress - brake pedal + accelerator pedal

required values
field X = Test OFF -> TEST ON

wait

required values
field X = BX-SX OK

upon achievement of values - release - brake pedal + accelerator pedal

XX - Basic settings group XXX
activate default settings

fully depress - brake pedal + accelerator pedal

required values
field X = Test OFF -> TEST ON

wait

required values
field X = Syst. OK

upon achievement of values - release - brake pedal + accelerator pedal

XX - Basic settings group XXX
activate default settings

fully depress - brake pedal + accelerator pedal

wait

required values
field X = XXXXxXXX
field X = XXXXxXXX

upon achievement of values - release - brake pedal + accelerator pedal

XX - Basic settings group XXX
activate default settings

increase rpm to XXXX - XXXX rpm

required values
field X > XXX °C

upon achievement of values - release - accelerator pedal

XX - Measured values group XXX

increase rpm to XXXX - XXXX rpm

required values
field X = XXXXXXXX

upon achievement of values - release - accelerator pedal

XX - Basic settings group XXX
activate default settings

fully depress - brake pedal + accelerator pedal

wait

required values
field X = BX-SX OK

upon achievement of values - release - brake pedal + accelerator pedal

XX - Basic settings group XXX
activate default settings

fully depress - brake pedal + accelerator pedal

required values
field X = XXXXXXXX

upon achievement of values - release - brake pedal + accelerator pedal

XX - Basic settings group XXX
activate default settings

fully depress - brake pedal + accelerator pedal

required values
field X = XXXXXXXX

upon achievement of values - release - brake pedal + accelerator pedal

XX - Basic settings group XXX
activate default settings

required values
field X = TEV OK

upon achievement of values - continue

XX - Basic settings group XXX
activate default settings

alternately operate the accelerator pedal
Xs = idling
XXs = XXXX rpm

required values
field X = xXxxxxXx

upon achievement of values - release - accelerator pedal

XX - Basic settings group XXX
activate default settings

sharply depress - accelerator pedal - engine speed = XXXX rpm

release - accelerator pedal

required values
field X = XXXXXXXX

upon achievement of values - release - brake pedal + accelerator pedal

engine speed = idling

wait X minutes

check download of the readiness code of the readiness functions

if values are not achieved:

check of error memory

do a test drive
- idling
- partial load
- full load (engine speed > XXXX rpm)
- deceleration

repeate this test

Log-in Buy