Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
Engines / Petrol / ME 7.5.20 general / creation of Readiness (207)
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
This operation was considered useful 1x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Conditions:
- number of faults = X
- engine temperature > XX°C (XX - Measured values group XXX field X)
- intake air temperature > X°C (XX - Measured values group XXX field X)
- catalyst temperature > XXX °C (XX - Measured values group XXX field X)
- on-board voltage > XXV (XX - Measured values group XXX field X)
- engine speed = X
- accelerator pedal - released (XX - Measured values group XXX field X)
Note:
The readiness Code must be created as the last diagnostics task. Later deletion of the memory could also result in deletion of the created readiness Code.
Start the engine, engine speed = idling
wait XXX s
switch on the ignition
connect with the control unit XX - engine
XX - Basic settings group XXX
activate default settings
wait
required values
field X = ADP-OK (may take several minutes)
upon achievement of values - continue
Start the engine, engine speed = idling
XX - Measured values group XXX
required values
field X = XXXXXXXX
field X = XXXXXXXX
may take several minutes
upon achievement of values - continue
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = XXXXXXXX
upon achievement of values - continue
release - brake pedal + accelerator pedal
Conditions:
- high beam = ON
- air-conditioning = ON
- rear window heating = ON
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = BX-SX OK
upon achievement of values - continue
release - brake pedal + accelerator pedal
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = BX-SX OK
upon achievement of values - continue
release - brake pedal + accelerator pedal
Conditions:
- high beam = OFF
- air-conditioning = OFF
- rear window heating = OFF
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = Syst. OK
upon achievement of values - continue
release - brake pedal + accelerator pedal
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = BX-SX OK
upon achievement of values - continue
release - brake pedal + accelerator pedal
XX - Basic settings group XXX
activate default settings
required values
field X = Syst. OK
upon achievement of values - continue
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = Syst. OK
upon achievement of values - continue
release - brake pedal + accelerator pedal
XX - Basic settings group XXX
activate default settings
required values
field X = TEV OK
upon achievement of values - continue
end
- number of faults = X
- engine temperature > XX°C (XX - Measured values group XXX field X)
- intake air temperature > X°C (XX - Measured values group XXX field X)
- catalyst temperature > XXX °C (XX - Measured values group XXX field X)
- on-board voltage > XXV (XX - Measured values group XXX field X)
- engine speed = X
- accelerator pedal - released (XX - Measured values group XXX field X)
Note:
The readiness Code must be created as the last diagnostics task. Later deletion of the memory could also result in deletion of the created readiness Code.
Start the engine, engine speed = idling
wait XXX s
switch on the ignition
connect with the control unit XX - engine
XX - Basic settings group XXX
activate default settings
wait
required values
field X = ADP-OK (may take several minutes)
upon achievement of values - continue
Start the engine, engine speed = idling
XX - Measured values group XXX
required values
field X = XXXXXXXX
field X = XXXXXXXX
may take several minutes
upon achievement of values - continue
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = XXXXXXXX
upon achievement of values - continue
release - brake pedal + accelerator pedal
Conditions:
- high beam = ON
- air-conditioning = ON
- rear window heating = ON
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = BX-SX OK
upon achievement of values - continue
release - brake pedal + accelerator pedal
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = BX-SX OK
upon achievement of values - continue
release - brake pedal + accelerator pedal
Conditions:
- high beam = OFF
- air-conditioning = OFF
- rear window heating = OFF
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = Syst. OK
upon achievement of values - continue
release - brake pedal + accelerator pedal
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = BX-SX OK
upon achievement of values - continue
release - brake pedal + accelerator pedal
XX - Basic settings group XXX
activate default settings
required values
field X = Syst. OK
upon achievement of values - continue
XX - Basic settings group XXX
activate default settings
fully depress - brake pedal + accelerator pedal
required values
field X = Syst. OK
upon achievement of values - continue
release - brake pedal + accelerator pedal
XX - Basic settings group XXX
activate default settings
required values
field X = TEV OK
upon achievement of values - continue
end
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.