Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
Engines / Petrol / SIMOS 3 general / creation of Readiness (60)
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Conditions:
- number of faults = X
- engine temperature > XX°C (XX - Measured values group XXX field X)
- intake air temperature > X°C (XX - Measured values group XXX field X)
- catalyst temperature > XXX °C (XX - Measured values group XXX field X)
- on-board voltage > XXV (XX - Measured values group XXX field X)
- engine speed = X
- accelerator pedal - released (XX - Measured values group XXX field X)
connect with the control unit XX - engine
XX - Basic settings group XXX
activate default settings
wait
required values
field X = ADP-OK (may take several minutes)
back
Start the engine, engine speed = idling
XX - Measured values group XXX
required values
field X > XXX °C (temperature of exhaust gases)
XX - Measured values group XXX
required values
field X = XXXXX
field X = XXXXX
XX?XX = heating of lambda probe(s)
XXX?X = readiness for operation
XXXX? = lambda control
upon achievement of values - continue
XX - Basic settings group XXX
depress and hold - brake pedal + accelerator pedal
the control unit increases the engine speed
required values
field X = XXXX rpm
field X > XXX °C (catalyst temperature)
field X = RX-SX-OK (may take several minutes)
upon achievement of values - release - brake pedal + accelerator pedal
back
engine speed = idling
XX - Basic settings group XXX
depress and hold - brake pedal + accelerator pedal
the control unit increases the engine speed
required values
field X > XXX °C (catalyst temperature)
field X = RX-SX-OK (may take several minutes)
upon achievement of values - release - brake pedal + accelerator pedal
back
engine speed = idling
XX - Basic settings group XXX
depress and hold - brake pedal + accelerator pedal
the control unit increases the engine speed
required values
field X > XXX °C (catalyst temperature)
field X = CAT-RX-OK (may take several minutes)
upon achievement of values - release - brake pedal + accelerator pedal
back
XX - Basic settings group XXX
depress and hold - brake pedal + accelerator pedal
the control unit increases the engine speed
required values
field X = TEV-OK (may take several minutes)
upon achievement of values - release - brake pedal + accelerator pedal
XX – error memory
desired condition: number of faults = X
XX - Measured values group XXX
required values
field X = XXXXXXXX (readiness)
xxxxxxx? = catalyst
xxxxxx?x = heating of catalyst
xxxxx?xx = EVAP
xxxx?xxx = secondary air system
xxx?xxxx = air-conditioning
xx?xxxxx = Lambda sensor(s)
x?xxxxxx = heating of lambda probe(s)
?xxxxxxx = exhaust recirculation
XX - end of communication
- number of faults = X
- engine temperature > XX°C (XX - Measured values group XXX field X)
- intake air temperature > X°C (XX - Measured values group XXX field X)
- catalyst temperature > XXX °C (XX - Measured values group XXX field X)
- on-board voltage > XXV (XX - Measured values group XXX field X)
- engine speed = X
- accelerator pedal - released (XX - Measured values group XXX field X)
connect with the control unit XX - engine
XX - Basic settings group XXX
activate default settings
wait
required values
field X = ADP-OK (may take several minutes)
back
Start the engine, engine speed = idling
XX - Measured values group XXX
required values
field X > XXX °C (temperature of exhaust gases)
XX - Measured values group XXX
required values
field X = XXXXX
field X = XXXXX
XX?XX = heating of lambda probe(s)
XXX?X = readiness for operation
XXXX? = lambda control
upon achievement of values - continue
XX - Basic settings group XXX
depress and hold - brake pedal + accelerator pedal
the control unit increases the engine speed
required values
field X = XXXX rpm
field X > XXX °C (catalyst temperature)
field X = RX-SX-OK (may take several minutes)
upon achievement of values - release - brake pedal + accelerator pedal
back
engine speed = idling
XX - Basic settings group XXX
depress and hold - brake pedal + accelerator pedal
the control unit increases the engine speed
required values
field X > XXX °C (catalyst temperature)
field X = RX-SX-OK (may take several minutes)
upon achievement of values - release - brake pedal + accelerator pedal
back
engine speed = idling
XX - Basic settings group XXX
depress and hold - brake pedal + accelerator pedal
the control unit increases the engine speed
required values
field X > XXX °C (catalyst temperature)
field X = CAT-RX-OK (may take several minutes)
upon achievement of values - release - brake pedal + accelerator pedal
back
XX - Basic settings group XXX
depress and hold - brake pedal + accelerator pedal
the control unit increases the engine speed
required values
field X = TEV-OK (may take several minutes)
upon achievement of values - release - brake pedal + accelerator pedal
XX – error memory
desired condition: number of faults = X
XX - Measured values group XXX
required values
field X = XXXXXXXX (readiness)
xxxxxxx? = catalyst
xxxxxx?x = heating of catalyst
xxxxx?xx = EVAP
xxxx?xxx = secondary air system
xxx?xxxx = air-conditioning
xx?xxxxx = Lambda sensor(s)
x?xxxxxx = heating of lambda probe(s)
?xxxxxxx = exhaust recirculation
XX - end of communication
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.