Engines / UDS Engines by part number / 01 - Engine [EV_ECM16TDI02103L906023NF 003008] / Adaptation of the deviation of the minimum number of injectors
Mark
Model
Control unit
Diagnostic operation
Mark
Škoda
VW
Audi
Seat
Porsche
Bentley
MAN
Service intervals
Engines
Gearboxes
Immobilizers
auxiliary heater
Model
UDS Engines by part number
Diesel
Petrol
Part 1 of the order number
03C
03E
03F
03H
03L
03N
03P
04B
04C
04E
04L
05C
05E
05L
06J
06K
07C
07P
0EA
1K8
2G0
2H6
36A
3G0
3W0
4G0
4G1
4G2
4G5
4H0
4K0
4KE
4L0
4L1
4L2
4M0
4M8
4ML
4N0
4S0
5FA
5G0
5H0
5N0
5NA
5WA
760
7P0
7P1
7P5
80A
81A
83A
8K0
8K1
8K2
8K5
8R0
8S0
8T0
8T1
8T2
8U0
8V0
8W0
8Y0
W03
W04
W4G
Control unit
Diagnostic operation
Start/stop - activation/deactivation
Customer limitation of maximum speed
Injector: corrective value - Test
Zeroing learning values DPF - If replaced: engine control unit/DPF
Zeroing learning values - Lambda sensor(s)
Zeroing learning values - Adaptation of the mean quantity value
Deletion of statistics memory - Start-stop
Automatic test procedure
Creation of readiness
Basic settings - exhaust gas return valve 1 (GX5)
Basic settings - turbo blower
Basic settings - Neutral gear sensor (G701)
Basic settings - adaptation - Test: throttle valve
Bleeding of fuel system
Test / activation of fuel pump and control relay
Evacuation of fuel tank
Test - Change-over valve for the cooler of the exhaust gas recirculation
Test - exhaust gas return valve 1 (GX5)
Test of filling and atmospheric pressure sensor (G31)
Test of intake air temperature sensor (G42)
Test of engine temperature sensor (G62)
Test of heating (glow) unit (J179)
Test of radiator fan control unit (J293)
Test - voltage: terminal 30 (J317)
Test - throttle valve: control unit (J338)
Test - low heat performance relay (J359)
Test - high heat performance relay (J360)
Test - system indicator light: glowing (K29)
Test - injector 1-4 (N30;N31;N32;N33)
Test - filling pressure control valve (N75) - variant 2
Test - Charge Pressure Controller - Position sensor (G581)
Test - engine control unit (J623) - power supply
Test - Fuel metering valve (N290)
Test - filling pressure control valve (N75)
Test / activation of fuel pump and control relay
Test of gas pedal position sensor 1; 2 (G79; G185)
Test of fuel temperature sensor (G81)
Test of pedal switches (cruise control)
Bleeding of fuel system
Evacuation of fuel tank
Zeroing learning values - Adaptation of the mean quantity value
Creation of readiness
Customer limitation of maximum speed
Deletion of statistics memory Start-stop
Bleeding of fuel system variant II
Evacuation of fuel tank II
Creation of readiness
Automatic test procedure
Test of gas pedal position sensor 1; 2 (G79; G185)
Test of intake air temperature sensor (G299)
Neutral gear sensor - adaptation
Test: temperature sensor - ambient temperature (G17)
Activation - fuel pump (G6)
Test - fuel pressure regulation vlave (N276)
Test - fuel pressure regulation vlave (N276) CAYA
Test - Emissions Indicator Light (K83)
Test - system indicator light: Diesel Particulate Filter (K231)
Test - idle stabilization
Test - Intake air mass sensor - test drive CAYD; CAYE
Test - fuel pressure - pressure sensor (G247) - general
Test - fuel pressure - pressure sensor (G247) CAYA
Test - fuel pressure - pressure sensor (G247)
Test - filling pressure control valve (N75)
Measurement of compression pressure
Test of filling pressure
Test of load signals for alternator
Test of air mass sensor (G70)
Test of filling and atmospheric pressure sensor
Test of gas pedal position sensor 1 (G79)
Test of gas pedal position sensor 2 (G185)
Test of DPF differential pressure sensor 1 (G450)
Test of DPF differential pressure sensor 1 (G505) CAYB
Test of engine temperature sensor - outlet from radiator (G83)
Test of engine temperature sensor - outlet from radiator (G83) CAYB
Test of exhaust gases temperature sensor 1; 3 (G235; G495; 648)
Test of cruise control
Settings - Charge Pressure Controller - turbo blade geometry sensor
Adaptation of the deviation of the minimum number of injectors
Reset of DPF clogging
Bleeding of fuel system - variant 2
Adaptation of DPF differential pressure sensor
Adaptation of injection valve after replacement
DPF regeneration - when vehicle is parked
DPF regeneration
DPF regeneration CAYB
Turbo blower - replacement (adaptation)
Zeroing learning values - Adaptation of the mean quantity value
Zeroing learning values - Quantity measuring unit - regulator valve
Creation of readiness
Adaptation of injection valve after replacement CLHx;CNHx
Adaptation of DPF differential pressure sensor
Test - Intake air mass sensor - test drive
Basic settings - exhaust gas flap
Test - Intake air mass sensor CUUx
Test - filling pressure control valve (N75) CUUx variant 1
Diagnostic procedure
This operation was considered useful 4x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR onl y You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Log-in
Buy
Conditions:
- software version > XXXX (TPIXXXXXX)
- engine speed = idling
- engine temperature >= XX°C
- may take several minutes (MAX . XX MIN )
connect with the control unit XX - engine
XX - Security access
enter value:
XXXXX = basic settings
Start
XX - Basic settings
select item in menu:
IDEXXXXX - Adaptation of the deviation of the minimum number of injectors
activate default settings
follow the diagnostics instructions - may take several minutes (MAX . XX MIN )
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR onl y You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Log-in
Buy