Engines / UDS Engines by part number / 01 - Engine [EV_ECM12TDI03103P906021L 001006] / Creation of readiness

Search: Search area:

Mark	Model	Control unit	Diagnostic operation

Mark

Select a vehicle make or a common group such as Service Intervals, Engines, Transmissions, Immobilizers and Independent Heaters.

Model

Part 1 of the order number Select the first three characters of the order number of the engine control unit. This number can be found in the VCDS when linked to the uniform in the SW order number field. Do not insert the ordering number from the control unit packaging here!!!

Select the first three characters of the order number of the engine control unit. This number can be found in the VCDS when linked to the uniform in the SW order number field. Do not insert the ordering number from the control unit packaging here!!!

Part 2 of the order number Select the first six characters of the order number of the engine control unit. This number can be found in the VCDS when linked to the uniform in the SW order number field. Do not enter the ordering number from the control unit packaging here!!!

Select the first six characters of the order number of the engine control unit. This number can be found in the VCDS when linked to the uniform in the SW order number field. Do not enter the ordering number from the control unit packaging here!!!

Part 3 of the order number Select the first nine characters of the order number of the engine control unit. This number can be found in the VCDS when linked to the uniform in the SW ordering number field. Do not enter the ordering number from the control unit packaging here!!!

Select the first nine characters of the order number of the engine control unit. This number can be found in the VCDS when linked to the uniform in the SW ordering number field. Do not enter the ordering number from the control unit packaging here!!!

Part 4 of the order number Select the order number of the engine control unit. This number can be found in the VCDS after connecting to the uniform in the SW ordering number field. Do not insert the ordering number from the control unit packaging here!!!

Select the order number of the engine control unit. This number can be found in the VCDS after connecting to the uniform in the SW ordering number field. Do not insert the ordering number from the control unit packaging here!!!

Control unit Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.

Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.

Diagnostic operation Select the desired diagnostic procedure.

Diagnostic procedure

This operation was considered useful 1x.

You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.

Log-in Buy

Conditions:
- engine speed = idling
- Error memory empty
- on-board voltage > XX.X V
- activate the hand brake
- gear lever - position N or D
- Start-Stop inactive

Note:
- The Readiness Code must be created as the last diagnostics task. Later deletion of the memory could also result in deletion of the created Readiness Code.

- the feasibility of this test may depend on the equipment of the control unit

connect with the control unit XX - engine

Advanced Measured Values

select item:

IDEXXXXX - Readiness

TIP: For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window

Start

Significance of individual code numbers (depending on the equipment):

xXXXXXXX - exhaust recirculation
XxXXXXXX - heating of lambda probe(s)
XXxXXXXX - Lambda sensor(s)
XXXxXXXX - air-conditioning
XXXXxXXX - secondary air system
XXXXXxXX - active charcoal system
XXXXXXxX - heating of catalyst
XXXXXXXx - catalyst

required value: XXXXXXXX

if values are not achieved - continue

XX - Basic settings

select item in drop-down menu: IDEXXXXX - Automatic test procedure

Start

follow the diagnostics instructions

required values: Successfully completed

if values are not achieved -> check of error memory

XX - end of communication

do a test drive:
- duration - must be minimum: XMIN
- XXx akceleraion -> deceleration -> akceleraion

further, do:

do a test drive:
- duration - must be minimum: XXs
- engine speed MIN. XXXX rpm
- engaged gear: X.

end

Log-in Buy