Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
Gearboxes / 7-speed / 7-speed Direct Shift Gearbox (DSG) (DSG/0AM) / basic settings
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
This operation was considered useful 4x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Conditions:
- number of faults = X
- engine temperature = XX-XX °C (XX - Measured values group XXX)
- gear engaged (P)
- engine speed = X
- ignition = ON
- brake pedal = depressed
Note:
done after repair of components (only):
- software version
- transmission mechatronics
- clutch
- error stored to error memory
connect with the control unit XX - gearbox electronics
XX - Basic settings group XXX
wait X - X MIN
required values:
field X = X
field X = X
field X = X
Start the engine
engine speed = idling
wait X - X MIN
required values:
field X = XXX
field X = X
field X = X
if displayed:
field X = XXX
field X = X
field X = X
-> Basic settings - incomplete
if displayed:
field X = XXX
field X = X
field X = X
-> Basic settings - failed, interrupted
switch ignition off for: XX s
switch on the ignition
check of error memory
XX - end of communication
do a test drive
Conditions:
- oil temperature - automatic transmission > XX °C (
XX - Measured values group XXX, field X)
- cruise control = OFF
with gear lever at position "D", accelerate in second gear with gas pedal depressed half-way
Stop and accelerate again in second gear with gas pedal depressed half-way.
Stop, select reverse gear and take-off twice
then drive forward for more than X seconds and then Stop
this is followed by driving for at least X minutes at XXXX - XXXX rpm in Xth gear, change pedal position, including use of full gas
this is followed by driving for at least X minutes at XXXX - XXXX rpm in Xth gear, change pedal position, including use of full gas
XX - Measured values group XXX
required values:
field X = X and higher
XX - Measured values group XXX
required values:
field X = X and higher
further, do: Test - play of clutch control mechanism KX, KX
Created on: XX.XX.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
- number of faults = X
- engine temperature = XX-XX °C (XX - Measured values group XXX)
- gear engaged (P)
- engine speed = X
- ignition = ON
- brake pedal = depressed
Note:
done after repair of components (only):
- software version
- transmission mechatronics
- clutch
- error stored to error memory
connect with the control unit XX - gearbox electronics
XX - Basic settings group XXX
wait X - X MIN
required values:
field X = X
field X = X
field X = X
Start the engine
engine speed = idling
wait X - X MIN
required values:
field X = XXX
field X = X
field X = X
if displayed:
field X = XXX
field X = X
field X = X
-> Basic settings - incomplete
if displayed:
field X = XXX
field X = X
field X = X
-> Basic settings - failed, interrupted
switch ignition off for: XX s
switch on the ignition
check of error memory
XX - end of communication
do a test drive
Conditions:
- oil temperature - automatic transmission > XX °C (
XX - Measured values group XXX, field X)
- cruise control = OFF
with gear lever at position "D", accelerate in second gear with gas pedal depressed half-way
Stop and accelerate again in second gear with gas pedal depressed half-way.
Stop, select reverse gear and take-off twice
then drive forward for more than X seconds and then Stop
this is followed by driving for at least X minutes at XXXX - XXXX rpm in Xth gear, change pedal position, including use of full gas
this is followed by driving for at least X minutes at XXXX - XXXX rpm in Xth gear, change pedal position, including use of full gas
XX - Measured values group XXX
required values:
field X = X and higher
XX - Measured values group XXX
required values:
field X = X and higher
further, do: Test - play of clutch control mechanism KX, KX
Created on: XX.XX.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.