Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
Immobilizers / 25 - 17 - Immobilizers / Generation IV / Adaptation of new keys
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
This operation was considered useful 3x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Conditions:
- it is necessary to adapt all keys (even why they are already functional)
- appliances OFF
- all keys must be either new, or already adapted to this vehicle
- on-board voltage > XXV
- During adaptation of each key, ensure that the rest of the keys are adequately far away from the ignition box (electromagnetic reader). The keys may lie on the front passenger’s Seat
Note:
- upon entering the incorrect Login code three times, immobiliser blocks
- a further attempt is possible after XX minutes of ignition on time and completed communication
- it is possible to adapt a maximum of X keys
connect with the control unit XX - Immobilizer
status check
XX - Measured values group XXX
required values:
field X = YES
if values are not achieved: check component: key
XX - Measured values group XXX
required values:
field X = X MIN (immobiliser blocking time)
field X = X MIN (immobiliser blocking time)
field X = X MIN (immobiliser blocking time)
if values are not achieved: do not interrupt communication, wait - required number of minutes
key - programming
XX - Security access
enter value: Vehicle PIN
for instance: XXXX enter as XXXXX
Start
XX - Adaptation channel XXX
if the channel shall not be available immediately, wait until it opens (some units are protected by a security check)
stored value = number of keys
enter value: total number of keys
Test
Save
key in ignition adapted
now, within a period of XXs, gradually switch the ignition on using all the keys to be adapted
an immobilizer indicator light blink confirms each key
check of error memory
Created on: X.XX.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
- it is necessary to adapt all keys (even why they are already functional)
- appliances OFF
- all keys must be either new, or already adapted to this vehicle
- on-board voltage > XXV
- During adaptation of each key, ensure that the rest of the keys are adequately far away from the ignition box (electromagnetic reader). The keys may lie on the front passenger’s Seat
Note:
- upon entering the incorrect Login code three times, immobiliser blocks
- a further attempt is possible after XX minutes of ignition on time and completed communication
- it is possible to adapt a maximum of X keys
connect with the control unit XX - Immobilizer
status check
XX - Measured values group XXX
required values:
field X = YES
if values are not achieved: check component: key
XX - Measured values group XXX
required values:
field X = X MIN (immobiliser blocking time)
field X = X MIN (immobiliser blocking time)
field X = X MIN (immobiliser blocking time)
if values are not achieved: do not interrupt communication, wait - required number of minutes
key - programming
XX - Security access
enter value: Vehicle PIN
for instance: XXXX enter as XXXXX
Start
XX - Adaptation channel XXX
if the channel shall not be available immediately, wait until it opens (some units are protected by a security check)
stored value = number of keys
enter value: total number of keys
Test
Save
key in ignition adapted
now, within a period of XXs, gradually switch the ignition on using all the keys to be adapted
an immobilizer indicator light blink confirms each key
check of error memory
Created on: X.XX.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.