Porsche / Cayenne (92) / 53 – parking brake EPB H51 (EV_ParkbA7) UDS / Replacement of brake pads
Mark | Model | Control unit | Diagnostic operation |
---|
Mark
![Select a vehicle make or a common group such as Service Intervals, Engines, Transmissions, Immobilizers and Independent Heaters.](/admin_assets/images/silk/comment.png)
Model
![Select a vehicle model or information group, for example Octavia III or Diesel, Petrol etc.](/admin_assets/images/silk/comment.png)
Control unit ![Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.](/admin_assets/images/silk/comment.png)
![Select the desired control unit as accurately as possible. The UDS identifier EV_xyz can be found in the VCDS after connecting to the control unit and then in the Extended Identification.](/admin_assets/images/silk/comment.png)
Diagnostic operation ![Select the desired diagnostic procedure.](/admin_assets/images/silk/comment.png)
![Select the desired diagnostic procedure.](/admin_assets/images/silk/comment.png)
Diagnostic procedure
This operation was considered useful 2x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Note:
- Error memory empty
- Functional tests of the brake pedal and parking brake may be done only with properly installed brake pads and callipers.
- Comply PRECISELY with the following procedure. Every step has its own substantiation.
- If you don precisely adhere to this procedure, the system could behave in an unexpected manner, which it need not be possible to repair.
wait for minimum XX seconds after brakes come to rest before the next step
due to an error in the firmware of some units, this could result in damage to the control module
release of parking brake
Conditions:
- connect battery charger
activate the hand brake
release the hand brake
Note:
- In this operation, it is normal that the LED on the parking brake and the warning indicator light on the dashboard blink rapidly.
connect with the control unit XX – parking brake
XX - Actuators
select item in drop-down menu: open Yoke
Start
the callipers open
!!! Wait for XX seconds after end of the motion of the brake pads !!!
XX - end of communication
replace the brake pad
engagement of parking brake
Conditions:
- connect battery charger
Note:
- In this operation, it is normal that the LED on the parking brake and the warning indicator light on the dashboard blink rapidly.
connect with the control unit XX – parking brake
XX - Actuators
select item in drop-down menu: Close Yoke
Start
the callipers close
XX - end of communication
activate the hand brake
release the hand brake
further, do: basic settings
Created on: XX.X.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
- Error memory empty
- Functional tests of the brake pedal and parking brake may be done only with properly installed brake pads and callipers.
- Comply PRECISELY with the following procedure. Every step has its own substantiation.
- If you don precisely adhere to this procedure, the system could behave in an unexpected manner, which it need not be possible to repair.
due to an error in the firmware of some units, this could result in damage to the control module
release of parking brake
Conditions:
- connect battery charger
activate the hand brake
release the hand brake
Note:
- In this operation, it is normal that the LED on the parking brake and the warning indicator light on the dashboard blink rapidly.
connect with the control unit XX – parking brake
XX - Actuators
select item in drop-down menu: open Yoke
Start
the callipers open
!!! Wait for XX seconds after end of the motion of the brake pads !!!
XX - end of communication
replace the brake pad
engagement of parking brake
Conditions:
- connect battery charger
Note:
- In this operation, it is normal that the LED on the parking brake and the warning indicator light on the dashboard blink rapidly.
connect with the control unit XX – parking brake
XX - Actuators
select item in drop-down menu: Close Yoke
Start
the callipers close
XX - end of communication
activate the hand brake
release the hand brake
further, do: basic settings
Created on: XX.X.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.