Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
Seat / Mii (AA) / 17 - Dashboard KOMBI [EV_KombiUDSMM9RM10 A05803] / Reset of fixed oil-change interval QI1-4
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
This operation was considered useful 4x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Conditions:
- engine speed = X
- Some control units may require that a non-zero number of the shop, importer and device be entered on the diagnostics equipment. This is the identification of the service / diagnostics equipment, which is provided by the manufacturer to the Volkswagen Group. Specific values may be required and/or in some case, it suffices that the values should be non-zero.
- applies only to control units with UDS protocol
Note:
- For vehicles with QI PR-codes, the Reseting of service, oil-change and inspection is done separately (WIV/ESI and FIX), even in the event that both service events occur simultaneously. It is thus always necessary to also check the second service event other than the one being handled. For instance, when doing service oil-change, it is necessary to check the time remaining to Inspection
- if the unit does not accept the values you have entered, it may happen that it is blocked by a previous unsuccessful attempt. In such case, turn-off the ignition for X minutes and repeat the operation
- it may happen that it is not possible to set the desired interval on the unit for the reason that the interval values were earlier changed unprofessionally. In such case, perform complete setting of the interval by procedure for change of interval
check data label on car for SIA limit that must be set
QIX = fixed service interval XXXXkm or XXX days
QIX = fixed service interval XXXXkm or XXX days
QIX = fixed service interval XXXXXkm or XXX days
QIX = fixed service interval XXXXXkm or XXX days
Reseting of oil-change - fixed interval
connect with the control unit XX - dashboard
XX - Adaptation UDS
select item in drop-down menu:
IDEXXXXX - WIV/ESI: Reseting of WIV/ESI
stored value: reset = service not required, notification on dashboard is not illuminated
stored value: warning active = service required, notification on dashboard is illuminated
enter value: reset
Start
IDEXXXXX - WIV/ESI: oil quality
enter value: bad oil quality
Start
IDEXXXXX - SIA: MAX value of journey to service
enter value: XXXXX (km)
Start
IDEXXXXX - SIA: MAX value of time to service
enter value: XXX (days)
Start
Note:
further, do: check of inspection necessity
- engine speed = X
- Some control units may require that a non-zero number of the shop, importer and device be entered on the diagnostics equipment. This is the identification of the service / diagnostics equipment, which is provided by the manufacturer to the Volkswagen Group. Specific values may be required and/or in some case, it suffices that the values should be non-zero.
- applies only to control units with UDS protocol
Note:
- For vehicles with QI PR-codes, the Reseting of service, oil-change and inspection is done separately (WIV/ESI and FIX), even in the event that both service events occur simultaneously. It is thus always necessary to also check the second service event other than the one being handled. For instance, when doing service oil-change, it is necessary to check the time remaining to Inspection
- if the unit does not accept the values you have entered, it may happen that it is blocked by a previous unsuccessful attempt. In such case, turn-off the ignition for X minutes and repeat the operation
- it may happen that it is not possible to set the desired interval on the unit for the reason that the interval values were earlier changed unprofessionally. In such case, perform complete setting of the interval by procedure for change of interval
check data label on car for SIA limit that must be set
QIX = fixed service interval XXXXkm or XXX days
QIX = fixed service interval XXXXkm or XXX days
QIX = fixed service interval XXXXXkm or XXX days
QIX = fixed service interval XXXXXkm or XXX days
Reseting of oil-change - fixed interval
connect with the control unit XX - dashboard
XX - Adaptation UDS
select item in drop-down menu:
IDEXXXXX - WIV/ESI: Reseting of WIV/ESI
stored value: reset = service not required, notification on dashboard is not illuminated
stored value: warning active = service required, notification on dashboard is illuminated
enter value: reset
Start
IDEXXXXX - WIV/ESI: oil quality
enter value: bad oil quality
Start
IDEXXXXX - SIA: MAX value of journey to service
enter value: XXXXX (km)
Start
IDEXXXXX - SIA: MAX value of time to service
enter value: XXX (days)
Start
Note:
further, do: check of inspection necessity
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.