Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
VW / Phaeton (3D) / 34 - clearance height control / Setting of the zero point of the height adjustment system
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
This operation was considered useful 4x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Conditions:
- gear engaged (P)
- engine speed = idling
basic value
Touareg (XL) - in front = XXX mm, in rear = XXX mm
Touareg (XL) - offroad = XXX mm, in rear = XXX mm
AX (XE) - in front = XXX mm, in rear = XXX mm
AX (XE) - sports chassis - in front = XXX mm, in rear = XXX mm
Phaeton - in front = XXX mm, in rear = XXX mm
Audi QX (XL) - in front = XXX mm, in rear = XXX mm
Audi AX (XF) - in front = XXX mm, in rear = XXX mm
Audi AX (XF) Allroad - in front = XXX mm, in rear = XXX mm
connect with the control unit XX - clearance height control
XX - Login (XX - Security access)
enter value XXXXX
Start
XX - Adaptation channel XXX (LF wheel)
measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value
Test
Save
XX - Adaptation channel XXX (RF wheel)
measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value
Test
Save
XX - Adaptation channel XXX (LR wheel)
measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value
Test
Save
XX - Adaptation channel XXX (RR wheel)
measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value
Test
Save
XX - Adaptation channel XXX
enter value: X
Test
Save
Created on: XX.XX.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
- gear engaged (P)
- engine speed = idling
basic value
Touareg (XL) - in front = XXX mm, in rear = XXX mm
Touareg (XL) - offroad = XXX mm, in rear = XXX mm
AX (XE) - in front = XXX mm, in rear = XXX mm
AX (XE) - sports chassis - in front = XXX mm, in rear = XXX mm
Phaeton - in front = XXX mm, in rear = XXX mm
Audi QX (XL) - in front = XXX mm, in rear = XXX mm
Audi AX (XF) - in front = XXX mm, in rear = XXX mm
Audi AX (XF) Allroad - in front = XXX mm, in rear = XXX mm
connect with the control unit XX - clearance height control
XX - Login (XX - Security access)
enter value XXXXX
Start
XX - Adaptation channel XXX (LF wheel)
measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value
Test
Save
XX - Adaptation channel XXX (RF wheel)
measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value
Test
Save
XX - Adaptation channel XXX (LR wheel)
measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value
Test
Save
XX - Adaptation channel XXX (RR wheel)
measure the distance from the wheel centre to the edge of the fender (lowest point on the outer side) and enter this value in mm as a new value
Test
Save
XX - Adaptation channel XXX
enter value: X
Test
Save
Created on: XX.XX.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.