Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
VW / Touareg USA (BP) / 53 - Parking brake EPB H51 [EV_ParkbA7 000006] / Basic settings
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
This operation was considered useful 8x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Conditions:
- Functional tests of the brake pedal and parking brake may be done only with properly installed brake pads and callipers.
- on-board voltage MIN XXV
- Start/Stop inactive
- the vehicle must stand on even ground
- engine speed idling
connect with the control unit XX – parking brake
depress and hold brake pedal
release the hand brake
activate the hand brake
release the hand brake
activate the hand brake
release brake pedal
release the hand brake
Advanced Measured Values
select item in menu:
IDEXXXXX - MASXXXXX Air gap - Before calibration - left
IDEXXXXX - MASXXXXX Air gap - Before calibration - right side
TIP For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window
Start
required values:
left: X,X - X,X mm
right side: X,X - X,X mm
the maximum permissible difference is X - X.X mm (left - right side)
upon non--achievement of condition:
- set the air gap according to the specification (manually):
left: X,X - X,X mm
right side: X,X - X,X mm
the maximum permissible difference is X - X.X mm (left - right side)
Picture documentation:
upon achievement of values: continue
XX - Security access
enter value: XXXXX
Start
XX - Basic settings
select item in drop-down menu: IDEXXXXX - Air gap - calibration
Start
follow the diagnostics instructions
wait XX s
XX - end of communication
Created on: XX.X.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
- Functional tests of the brake pedal and parking brake may be done only with properly installed brake pads and callipers.
- on-board voltage MIN XXV
- Start/Stop inactive
- the vehicle must stand on even ground
- engine speed idling
connect with the control unit XX – parking brake
depress and hold brake pedal
release the hand brake
activate the hand brake
release the hand brake
activate the hand brake
release brake pedal
release the hand brake
Advanced Measured Values
select item in menu:
IDEXXXXX - MASXXXXX Air gap - Before calibration - left
IDEXXXXX - MASXXXXX Air gap - Before calibration - right side
TIP For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window
Start
required values:
left: X,X - X,X mm
right side: X,X - X,X mm
the maximum permissible difference is X - X.X mm (left - right side)
upon non--achievement of condition:
- set the air gap according to the specification (manually):
left: X,X - X,X mm
right side: X,X - X,X mm
the maximum permissible difference is X - X.X mm (left - right side)
Picture documentation:
upon achievement of values: continue
XX - Security access
enter value: XXXXX
Start
XX - Basic settings
select item in drop-down menu: IDEXXXXX - Air gap - calibration
Start
follow the diagnostics instructions
wait XX s
XX - end of communication
Created on: XX.X.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.