Diagnostic procedures for a VAG diagnostics
Database for coding vehicle control units Volkswagen - VAG
Software versions
VIN - Code validator
VW / Transporter T6 (7H) / 17 - Dashboard KOMBI VDD MQBAB [EV_DashBoardVDDMQBAB 009071] / Change to variable oil-change interval QI
Search:
Search area:
| Mark | Model | Control unit | Diagnostic operation |
|---|
Mark 
Model
Control unit
Diagnostic operation
Diagnostic procedure
This operation was considered useful 2x.
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.
Conditions:
- engine speed = X
- Some control units may require that a non-zero number of the shop, importer and device be entered on the diagnostics equipment. This is the identification of the service / diagnostics equipment, which is provided by the manufacturer to the Volkswagen Group. Specific values may be required and/or in some case, it suffices that the values should be non-zero.
- applies only to control units with UDS protocol
Note:
- this function is recommended only upon oil change and service inspection to prevent overrun of some service events
-this function is available only in a dashboard with factory set flexible service interval.
- For vehicles with QI PR-codes, the Reseting of service, oil-change and inspection is done separately (WIV/ESI and FIX), even in the event that both service events occur simultaneously. It is thus always necessary to also check the second service event other than the one being handled. For instance, when doing service oil-change, it is necessary to check the time remaining to Inspection
- if the unit does not accept the values you have entered, it may happen that it is blocked by a previous unsuccessful attempt. In such case, turn-off the ignition for X minutes and repeat the operation
- it may happen that it is not possible to set the desired interval on the unit for the reason that the interval values were earlier changed unprofessionally. In such case, perform complete setting of the interval by procedure for change of interval
connect with the control unit XX - dashboard
select item in drop-down menu:
IDEXXXXX - WIV/ESI: oil quality
enter value: good oil quality
Start
IDEXXXXX - WIV/ESI: MIN. km/inspection
enter value: XXXXX (km)
Start
IDEXXXXX - WIV/ESI: MAX. km/inspection
enter value: XXXXX (km)
Start
IDEXXXXX - WIV/ESI: MIN. time in-between inspections
enter value: XXX (days)
Start
IDEXXXXX - WIV/ESI: MAX. time in-between inspections
enter value: XXX (days)
Start
- engine speed = X
- Some control units may require that a non-zero number of the shop, importer and device be entered on the diagnostics equipment. This is the identification of the service / diagnostics equipment, which is provided by the manufacturer to the Volkswagen Group. Specific values may be required and/or in some case, it suffices that the values should be non-zero.
- applies only to control units with UDS protocol
Note:
- this function is recommended only upon oil change and service inspection to prevent overrun of some service events
-this function is available only in a dashboard with factory set flexible service interval.
- For vehicles with QI PR-codes, the Reseting of service, oil-change and inspection is done separately (WIV/ESI and FIX), even in the event that both service events occur simultaneously. It is thus always necessary to also check the second service event other than the one being handled. For instance, when doing service oil-change, it is necessary to check the time remaining to Inspection
- if the unit does not accept the values you have entered, it may happen that it is blocked by a previous unsuccessful attempt. In such case, turn-off the ignition for X minutes and repeat the operation
- it may happen that it is not possible to set the desired interval on the unit for the reason that the interval values were earlier changed unprofessionally. In such case, perform complete setting of the interval by procedure for change of interval
connect with the control unit XX - dashboard
select item in drop-down menu:
IDEXXXXX - WIV/ESI: oil quality
enter value: good oil quality
Start
IDEXXXXX - WIV/ESI: MIN. km/inspection
enter value: XXXXX (km)
Start
IDEXXXXX - WIV/ESI: MAX. km/inspection
enter value: XXXXX (km)
Start
IDEXXXXX - WIV/ESI: MIN. time in-between inspections
enter value: XXX (days)
Start
IDEXXXXX - WIV/ESI: MAX. time in-between inspections
enter value: XXX (days)
Start
You are not logged! System works in DEMO mode only now where numbers are replaced with X characters. For 49 EUR only You will get access into full system. You can pay by credit card or bank transfer. Click BUY button for purchase and You will get login to diagnostic procedures database imediatelly.