Dijagnostičke procedure za VAG dijagnostiku
Baza podataka za kodiranje kontrolnih jedinica Volkswagen - VAG
Software versions
Validator VIN koda- Scan Explorer
Audi / Audi A6 /A7 (F2) / 13 - Regulacija odstojanja [EV_ACCBOSCHAU65X 002036] / Adaptivna kontrola rastojanja - podešavanje
Traži - Search:
Područje pretrage:
| Proizvođač | Model | Kontrolna jedinica - Control unit | Dijagnostička operacija - Diagnostic operation |
|---|
Proizvođač 
Model
Kontrolna jedinica - Control unit
Dijagnostička operacija - Diagnostic operation
Dijagnostička procedura
Niste prijavljeni! Sistem radi u DEMO modu samo sada kada su brojevi zamenjeni X znakovima. Za samo 49 EUR dobićete pristup celom sistemuu. Možete platiti kreditnom karticom ili bankovnim prenosom. Kliknite [KUPI] za kupovinu i odmah dobijate prijavu u bazu podataka dijagnostičkih postupaka.
Note:
done after repair of components:
• test / wheel alignment
• front cross-member
• distance control - control unit
Conditions:
• locate the vehicle on a device for measurement and setting of the wheel alignment
• install calibration jig: VAS XXXX or VAS XXXX or calibration plate
• distance calibration plate - logo Audi = XXXcm+-X,X cm
• You can find more important information about this procedure in the erWin servicing manual
X) control unit JXXX (right side)
connect with the control unit XX - adaptive distance control
XX - Actuators
select item in menu:
IDEXXXXX - calibration
In the Actuators window, click Measured values and select the items you want to visualize.
IDEXXXXX - calibration - instructions
Adjust mirror to position X
XX - Actuators -> Start
follow the diagnostics instructions
required value: calibration OK
back
Advanced Measured Values
TIP: For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window
select item in menu:
IDEXXXXX-MASXXXXX - settings up left - direction
IDEXXXXX-MASXXXXX - settings up left - rotation
IDEXXXXX-MASXXXXX - settings up right side - direction
IDEXXXXX-MASXXXXX - settings up right side - rotation
Adjust bolts according to description. If the bolts are moved, the previous steps must be repeated until the unit is adjusted properly.
X) control unit JXXX (left)
connect with the control unit XB - adaptive distance control II
XX - Actuators
select item in menu:
IDEXXXXX - calibration
In the Actuators window, click Measured values and select the items you want to visualize.
IDEXXXXX - calibration - instructions
Adjust mirror to position X
XX - Actuators -> Start
follow the diagnostics instructions
required value: calibration OK
back
Advanced Measured Values
TIP: For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window
select item in menu:
IDEXXXXX-MASXXXXX - settings up left - direction
IDEXXXXX-MASXXXXX - settings up left - rotation
IDEXXXXX-MASXXXXX - settings up right side - direction
IDEXXXXX-MASXXXXX - settings up right side - rotation
Adjust bolts according to description. If the bolts are moved, the previous steps must be repeated until the unit is adjusted properly.
End of test
This procedure was generated by robot VISHunter XXXXXX X.X.XXXX at XX:XX:XX on ACS-NTB
done after repair of components:
• test / wheel alignment
• front cross-member
• distance control - control unit
Conditions:
• locate the vehicle on a device for measurement and setting of the wheel alignment
• install calibration jig: VAS XXXX or VAS XXXX or calibration plate
• distance calibration plate - logo Audi = XXXcm+-X,X cm
• You can find more important information about this procedure in the erWin servicing manual
X) control unit JXXX (right side)
connect with the control unit XX - adaptive distance control
XX - Actuators
select item in menu:
IDEXXXXX - calibration
In the Actuators window, click Measured values and select the items you want to visualize.
IDEXXXXX - calibration - instructions
Adjust mirror to position X
XX - Actuators -> Start
follow the diagnostics instructions
required value: calibration OK
back
Advanced Measured Values
TIP: For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window
select item in menu:
IDEXXXXX-MASXXXXX - settings up left - direction
IDEXXXXX-MASXXXXX - settings up left - rotation
IDEXXXXX-MASXXXXX - settings up right side - direction
IDEXXXXX-MASXXXXX - settings up right side - rotation
Adjust bolts according to description. If the bolts are moved, the previous steps must be repeated until the unit is adjusted properly.
X) control unit JXXX (left)
connect with the control unit XB - adaptive distance control II
XX - Actuators
select item in menu:
IDEXXXXX - calibration
In the Actuators window, click Measured values and select the items you want to visualize.
IDEXXXXX - calibration - instructions
Adjust mirror to position X
XX - Actuators -> Start
follow the diagnostics instructions
required value: calibration OK
back
Advanced Measured Values
TIP: For easier search in the menu, enter the code IDE, ENG or MAS into the "Filter" window
select item in menu:
IDEXXXXX-MASXXXXX - settings up left - direction
IDEXXXXX-MASXXXXX - settings up left - rotation
IDEXXXXX-MASXXXXX - settings up right side - direction
IDEXXXXX-MASXXXXX - settings up right side - rotation
Adjust bolts according to description. If the bolts are moved, the previous steps must be repeated until the unit is adjusted properly.
End of test
This procedure was generated by robot VISHunter XXXXXX X.X.XXXX at XX:XX:XX on ACS-NTB
Niste prijavljeni! Sistem radi u DEMO modu samo sada kada su brojevi zamenjeni X znakovima. Za samo 49 EUR dobićete pristup celom sistemuu. Možete platiti kreditnom karticom ili bankovnim prenosom. Kliknite [KUPI] za kupovinu i odmah dobijate prijavu u bazu podataka dijagnostičkih postupaka.