Dijagnostičke procedure za VAG dijagnostiku
Baza podataka za kodiranje kontrolnih jedinica Volkswagen - VAG
Software versions
Validator VIN koda- Scan Explorer
Škoda / Octavia 4 (NX) / 03 - Ektronika kočnica ABS [EV_Brake1ESCEPBMQB37W 007048] / Zamena kočionih obloga
Traži - Search:
Područje pretrage:
| Proizvođač | Model | Kontrolna jedinica - Control unit | Dijagnostička operacija - Diagnostic operation |
|---|
Proizvođač 
Model
Kontrolna jedinica - Control unit
Dijagnostička operacija - Diagnostic operation
Dijagnostička procedura
This operation was considered useful 9x.
Niste prijavljeni! Sistem radi u DEMO modu samo sada kada su brojevi zamenjeni X znakovima. Za samo 49 EUR dobićete pristup celom sistemuu. Možete platiti kreditnom karticom ili bankovnim prenosom. Kliknite [KUPI] za kupovinu i odmah dobijate prijavu u bazu podataka dijagnostičkih postupaka.
Note:
• This operation may required that the SFD be unlocked!
• Functional tests of the brake pedal and parking brake may be done only with properly installed brake pads and callipers.
• Comply PRECISELY with the following procedure. Every step has its own substantiation.
• If you don precisely adhere to this procedure, the system could behave in an unexpected manner, which it need not be possible to repair.
wait for minimum XX seconds after brakes come to rest before the next step
due to an error in the firmware of some units, this could result in damage to the control module
release of parking brake
Conditions:
• bonnet open
• connect battery charger
• brake pedal - released
activate the hand brake
release the hand brake
Note:
- In this operation, it is normal that the LED on the parking brake and the warning indicator light on the dashboard blink rapidly.
connect with the control unit XX - brake electronics
XX - Basic settings
select item in drop-down menu: IDEXXXXX-ENGXXXXXX- Mode for replacement of the brake pads - Start
Start
the callipers open
!!! Wait for XX seconds after end of the motion of the brake pads !!!
XX - end of communication
replace the brake pad
engagement of parking brake
Conditions:
• bonnet open
• connect battery charger
• brake pedal - released
Note:
- In this operation, it is normal that the LED on the parking brake and the warning indicator light on the dashboard blink rapidly.
connect with the control unit XX - brake electronics
XX - Basic settings
select item in drop-down menu: IDEXXXXX-ENGXXXXXX- Mode for replacement of the brake pads - end
Start
the callipers close
XX - end of communication
activate the hand brake
release the hand brake
functional test
Conditions:
• bonnet open
• connect battery charger
• the vehicle must be standing on a level surface
• brake pedal = released
activate the hand brake
release the hand brake
connect with the control unit XX - brake electronics
XX - Basic settings
select item in drop-down menu: IDEXXXXX-ENGXXXXXX - Check of the EPB – electromechanical parking brake function
Start
The callipers run through X braking and release cycles.
!!! Wait for XX seconds after end of the motion of the brake pads !!!
XX - end of communication
Created on: XX.X.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
• This operation may required that the SFD be unlocked!
• Functional tests of the brake pedal and parking brake may be done only with properly installed brake pads and callipers.
• Comply PRECISELY with the following procedure. Every step has its own substantiation.
• If you don precisely adhere to this procedure, the system could behave in an unexpected manner, which it need not be possible to repair.
due to an error in the firmware of some units, this could result in damage to the control module
release of parking brake
Conditions:
• bonnet open
• connect battery charger
• brake pedal - released
activate the hand brake
release the hand brake
Note:
- In this operation, it is normal that the LED on the parking brake and the warning indicator light on the dashboard blink rapidly.
connect with the control unit XX - brake electronics
XX - Basic settings
select item in drop-down menu: IDEXXXXX-ENGXXXXXX- Mode for replacement of the brake pads - Start
Start
the callipers open
!!! Wait for XX seconds after end of the motion of the brake pads !!!
XX - end of communication
replace the brake pad
engagement of parking brake
Conditions:
• bonnet open
• connect battery charger
• brake pedal - released
Note:
- In this operation, it is normal that the LED on the parking brake and the warning indicator light on the dashboard blink rapidly.
connect with the control unit XX - brake electronics
XX - Basic settings
select item in drop-down menu: IDEXXXXX-ENGXXXXXX- Mode for replacement of the brake pads - end
Start
the callipers close
XX - end of communication
activate the hand brake
release the hand brake
functional test
Conditions:
• bonnet open
• connect battery charger
• the vehicle must be standing on a level surface
• brake pedal = released
activate the hand brake
release the hand brake
connect with the control unit XX - brake electronics
XX - Basic settings
select item in drop-down menu: IDEXXXXX-ENGXXXXXX - Check of the EPB – electromechanical parking brake function
Start
The callipers run through X braking and release cycles.
!!! Wait for XX seconds after end of the motion of the brake pads !!!
XX - end of communication
Created on: XX.X.XXXX XX:XX:XX (hnz) Copyright © XXXX-XXXX, AutoComSoft Ltd All rights reserved.
Niste prijavljeni! Sistem radi u DEMO modu samo sada kada su brojevi zamenjeni X znakovima. Za samo 49 EUR dobićete pristup celom sistemuu. Možete platiti kreditnom karticom ili bankovnim prenosom. Kliknite [KUPI] za kupovinu i odmah dobijate prijavu u bazu podataka dijagnostičkih postupaka.